محول حفزي

(تم التحويل من Catalytic converter)
محول حفزي ثلاثي الاتجاهات على شاحنة دودج رام 1996 تدور بالجاسولين.
محاكاة للسريان داخل محول حفزي

المحول الحفزي catalytic converter هو جهاز للتحكم في الانبعاثات يحوّل الغازات السامة والملوثات في غاز العادم إلى ملوثات أقل سمية بحفز تفاعل أكسدة-اختزال. المحولات الحفزية المستخدمة مع محركات الاحتراق الداخلي التي تعمل بالبترول (جاسولين) أو بالديزل — بما في ذلك محركات الحرق اللين وكذلك سخانات الكيروسين والمواقد.

أول استخدام على نطاق واسع للمحولات الحفزية كان في سوق سيارات الولايات المتحدة. للالتزام بالتنظيمات المشددة للوكالة الأمريكية لحماية البيئة حول انبعاثات العادم، فللسيارات التي تعمل بالجاسولين بدءاً من سنة موديل 1975 أصبح لزاماً عليها أن تُزوَّد بمحول حفزي.[1][2][3][4] تلك المحولات "ثنائية الاتحاه" جمعت الأكسجين مع أول أكسيد الكربون (CO) و الهيدروكربونات غير المحترقة (HC) لانتاج ثاني أكسيد الكربون (CO2) و ماء (H2O). وفي 1981، أصبحت المحولات الحفزية ثنائية الاتجاه لاغية بظهور المحولات "ثلاثية الاتجاه" التي أيضاً تختزل أكاسيد النيتروجين (NOx);[1] إلا أن المحولات ثنائية الاتجاه مازالت تستخدم لمحركات الحرق اللين. وذلك لأن المحولات ثلاثية الاتجاه تتطلب إما احتراقي غني أو حسابي لتختزل بنجاح أكاسيد النيتروجين.

Although catalytic converters are most commonly applied to exhaust systems in automobiles, they are also used on electrical generators, forklifts, mining equipment, trucks, buses, locomotives and motorcycles. They are also used on some wood stoves to control emissions.[5] This is usually in response to government regulation, either through direct environmental regulation or through health and safety regulations. A catalytic converter has to be changed every 100 000 / 120 000 km in order to be efficient. It is important to recycle this part of the car. [6]

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

التاريخ

The catalytic converter was invented by Eugene Houdry, a French mechanical engineer and expert in catalytic oil refining,[7] who moved to the United States in 1930. When the results of early studies of smog in Los Angeles were published, Houdry became concerned about the role of smoke stack exhaust and automobile exhaust in air pollution and founded a company called Oxy-Catalyst. Houdry first developed catalytic converters for smoke stacks called "cats" for short, and later developed catalytic converters for warehouse forklifts that used low grade, unleaded gasoline.[8] In the mid-1950s, he began research to develop catalytic converters for gasoline engines used on cars. He was awarded United States Patent 2,742,437 for his work.[9]

Widespread adoption of catalytic converters did not occur until more stringent emission control regulations forced the removal of the anti-knock agent tetraethyl lead from most types of gasoline. Lead is a "catalyst poison" and would effectively disable a catalytic converter by forming a coating on the catalyst's surface.[10]

Catalytic converters were further developed by a series of engineers including John J. Mooney, Carl D. Keith, Antonio Eleazar at the Engelhard Corporation,[11] creating the first production catalytic converter in 1973.[12]

William C. Pfefferle developed a catalytic combustor for gas turbines in the early 1970s, allowing combustion without significant formation of nitrogen oxides and carbon monoxide.[13][14]


الإنشاء

مقطع في محول ذي قلب فلزي
محول ذو قلب سيراميكي

إنشاء المحول الحفزي يكون كما يلي:

  1. The catalyst support or substrate. For automotive catalytic converters, the core is usually a ceramic monolith with a honeycomb structure. Metallic foil monoliths made of Kanthal (FeCrAl)[15] are used in applications where particularly high heat resistance is required.[15] Either material is designed to provide a large surface area. The cordierite ceramic substrate used in most catalytic converters was invented by Rodney Bagley, Irwin Lachman and Ronald Lewis at Corning Glass, for which they were inducted into the National Inventors Hall of Fame in 2002.[1]
  2. The washcoat. A washcoat is a carrier for the catalytic materials and is used to disperse the materials over a large surface area. Aluminum oxide, titanium dioxide, silicon dioxide, or a mixture of silica and alumina can be used. The catalytic materials are suspended in the washcoat prior to applying to the core. Washcoat materials are selected to form a rough, irregular surface, which greatly increases the surface area compared to the smooth surface of the bare substrate. This in turn maximizes the catalytically active surface available to react with the engine exhaust. The coat must retain its surface area and prevent sintering of the catalytic metal particles even at high temperatures (1000 °C).[16]
  3. Ceria or ceria-zirconia. These oxides are mainly added as oxygen storage promoters.[17]
  4. The catalyst itself is most often a mix of precious metal. Platinum is the most active catalyst and is widely used, but is not suitable for all applications because of unwanted additional reactions and high cost. Palladium and rhodium are two other precious metals used. Rhodium is used as a reduction catalyst, palladium is used as an oxidation catalyst, and platinum is used both for reduction and oxidation. Cerium, iron, manganese and nickel are also used, although each has limitations. Nickel is not legal for use in the European Union because of its reaction with carbon monoxide into toxic nickel tetracarbonyl.[بحاجة لمصدر] Copper can be used everywhere except Japan.[مطلوب توضيح]


Upon failure, a catalytic converter can be recycled into scrap. The precious metals inside the converter, including platinum, palladium, and rhodium, are extracted.

تحديد موضع المحولات الحفزية

Catalytic converters require a temperature of 400 °C (752 °F) to operate effectively. Therefore, they are placed as close to the engine as possible, or one or more smaller catalytic converters (known as "pre-cats") are placed immediately after the exhaust manifold.

الأنواع

ثنائية الطرق

A 2-way (or "oxidation", sometimes called an "oxi-cat") catalytic converter has two simultaneous tasks:

  1. Oxidation of carbon monoxide to carbon dioxide: 2 CO + O2 → 2 CO2
  2. Oxidation of hydrocarbons (unburnt and partially burned fuel) to carbon dioxide and water: CxH2x+2 + [(3x+1)/2] O2 → x CO2 + (x+1) H2O (a combustion reaction)

This type of catalytic converter is widely used on diesel engines to reduce hydrocarbon and carbon monoxide emissions. They were also used on gasoline engines in American- and Canadian-market automobiles until 1981. Because of their inability to control oxides of nitrogen, they were superseded by three-way converters.

ثلاثي الطرق

Three-way catalytic converters have the additional advantage of controlling the emission of nitric oxide (NO) and nitrogen dioxide (NO2) (both together abbreviated with NO
x
and not to be confused with nitrous oxide (N2O)), which are precursors to acid rain and smog.[18]

منذ 1981, "three-way" (oxidation-reduction) catalytic converters have been used in vehicle emission control systems in the United States and Canada; many other countries have also adopted stringent vehicle emission regulations that in effect require three-way converters on gasoline-powered vehicles. The reduction and oxidation catalysts are typically contained in a common housing; however, in some instances, they may be housed separately. A three-way catalytic converter has three simultaneous tasks:[18]

Reduction of nitrogen oxides to nitrogen (N2)

Oxidation of carbon, hydrocarbons, and carbon monoxide to carbon dioxide

These three reactions occur most efficiently when the catalytic converter receives exhaust from an engine running slightly above the stoichiometric point. For gasoline combustion, this ratio is between 14.6 and 14.8 parts air to one part fuel, by weight. The ratio for autogas (or liquefied petroleum gas LPG), natural gas, and ethanol fuels can vary significantly for each, notably so with oxygenated or alcohol based fuels, with e85 requiring approximately 34% more fuel, requiring modified fuel system tuning and components when using those fuels. In general, engines fitted with 3-way catalytic converters are equipped with a computerized closed-loop feedback fuel injection system using one or more oxygen sensors,[بحاجة لمصدر] though early in the deployment of three-way converters, carburetors equipped with feedback mixture control were used.

Three-way converters are effective when the engine is operated within a narrow band of air-fuel ratios near the stoichiometric point.[19] Total conversion efficiency falls very rapidly when the engine is operated outside of this band. Slightly lean of stoichiometric, the exhaust gases from the engine contain excess oxygen, the production of NO
x
by the engine increases, and the efficiency of the catalyst at reducing NOx falls off rapidly. However, the conversion of HC and CO is very efficient due to the available oxygen, oxidizing to H2O and CO2. Slightly rich of stoichiometric, the production of CO and unburnt HC by the engine starts to increase dramatically, available oxygen decreases, and the efficiency of the catalyst for oxidizing CO and HC decreases significantly, especially as stored oxygen becomes depleted. However, the efficiency of the catalyst at reducing NOx is good, and the production of NOx by the engine decreases. To maintain catalyst efficiency, the air:fuel ratio must stay close to stoichiometric and not remain rich or lean for too long.

Closed-loop engine control systems are used for effective operation of three-way catalytic converters because of this continuous rich-lean balance required for effective NO
x
reduction and HC+CO oxidation. The control system allows the catalyst to release oxygen during slightly rich operating conditions, which oxidizes CO and HC under conditions that also favor the reduction of NOx. Before the stored oxygen is depleted, the control system shifts the air:fuel ratio to become slightly lean, improving HC and CO oxidation while storing additional oxygen in the catalyst material, at a small penalty in NOx reduction efficiency. Then the air:fuel mixture is brought back to slightly rich, at a small penalty in CO and HC oxidation efficiency, and the cycle repeats. Efficiency is improved when this oscillation around the stoichiometric point is small and carefully controlled.[20]

Closed-loop control under light to moderate load is accomplished by using one or more oxygen sensors in the exhaust system. When oxygen is detected by the sensor, the air:fuel ratio is lean of stoichiometric, and when oxygen is not detected, it is rich. The control system adjusts the rate of fuel being injected into the engine based on this signal to keep the air:fuel ratio near the stoichiometric point in order to maximize catalyst conversion efficiency. The control algorithm is also affected by the time delay between the adjustment of the fuel flow rate and the sensing of the changed air:fuel ratio by the sensor, as well as the sigmoidal response of the oxygen sensors. Typical control systems are designed to rapidly sweep the air:fuel ratio such that it oscillates slightly around the stoichiometric point, staying near the optimal efficiency point while managing the levels of stored oxygen and unburnt HC.[21]

Closed loop control is often not used during high load/maximum power operation, when an increase in emissions is permitted and a rich mixture is commanded to increase power and prevent exhaust gas temperature from exceeding design limits. This presents a challenge for control system and catalyst design. During such operations, large amounts of unburnt HC are produced by the engine, well beyond the capacity of the catalyst to release oxygen. The surface of the catalyst quickly becomes saturated with HC. When returning to lower power output and leaner air:fuel ratios, the control system must prevent excessive oxygen from reaching the catalyst too quickly, as this will rapidly burn the HC in the already hot catalyst, potentially exceeding the design temperature limit of the catalyst. Excessive catalyst temperature can prematurely age the catalyst, reducing its efficiency before reaching its design lifetime. Excessive catalyst temperature can also be caused by cylinder misfire, which continuously flows unburnt HC combined with oxygen to the hot catalyst, burning in the catalyst and increasing its temperature.[22]

التفاعلات غير المرغوب فيها

Unwanted reactions result in the formation of hydrogen sulfide and ammonia, which poison catalysts. Nickel or manganese is sometimes added to the washcoat to limit hydrogen-sulfide emissions.[بحاجة لمصدر] Sulfur-free or low-sulfur fuels eliminate or minimize problems with hydrogen sulfide.


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

محركات الديزل

For compression-ignition (i.e., diesel) engines, the most commonly used catalytic converter is the diesel oxidation catalyst (DOC). DOCs contain palladium and/or platinum supported on alumina. This catalyst converts particulate matter (PM), hydrocarbons, and carbon monoxide to carbon dioxide and water. These converters often operate at 90 percent efficiency, virtually eliminating diesel odor and helping reduce visible particulates. These catalysts are ineffective for NO
x
, so NO
x
emissions from diesel engines are controlled by exhaust gas recirculation (EGR).

In 2010, most light-duty diesel manufacturers in the U.S. added catalytic systems to their vehicles to meet federal emissions requirements. Two techniques have been developed for the catalytic reduction of NO
x
emissions under lean exhaust conditions, selective catalytic reduction (SCR) and the NO
x
adsorber
.

Instead of precious metal-containing NO
x
absorbers, most manufacturers selected base-metal SCR systems that use a reagent such as ammonia to reduce the NO
x
into nitrogen and water.[23] Ammonia is supplied to the catalyst system by the injection of urea into the exhaust, which then undergoes thermal decomposition and hydrolysis into ammonia. The urea solution is also referred to as diesel exhaust fluid (DEF).

Diesel exhaust contains relatively high levels of particulate matter. Catalytic converters remove only 20–40% of PM so particulates are cleaned up by a soot trap or diesel particulate filter (DPF). In the U.S., all on-road light, medium, and heavy-duty diesel-powered vehicles built after 1 January 2007, are subject to diesel particulate emission limits, and so are equipped with a 2-way catalytic converter and a diesel particulate filter.[بحاجة لمصدر] As long as the engine was manufactured before 1 January 2007, the vehicle is not required to have the DPF system.[بحاجة لمصدر] This led to an inventory runup by engine manufacturers in late 2006 so they could continue selling pre-DPF vehicles well into 2007.[24]

محركات الإشعال بشرارة الحرق الفعال

For lean-burn spark-ignition engines, an oxidation catalyst is used in the same manner as in a diesel engine. Emissions from lean burn spark ignition engines are very similar to emissions from a diesel compression ignition engine.

التركيب

Many vehicles have a close-coupled catalytic converter located near the engine's exhaust manifold. The converter heats up quickly, due to its exposure to the very hot exhaust gases, enabling it to reduce undesirable emissions during the engine warm-up period. This is achieved by burning off the excess hydrocarbons which result from the extra-rich mixture required for a cold start.

When catalytic converters were first introduced, most vehicles used carburetors that provided a relatively rich air-fuel ratio. Oxygen (O2) levels in the exhaust stream were therefore generally insufficient for the catalytic reaction to occur efficiently. Most designs of the time therefore included secondary air injection, which injected air into the exhaust stream. This increased the available oxygen, allowing the catalyst to function as intended.

Some three-way catalytic converter systems have air injection systems with the air injected between the first (NO
x
reduction) and second (HC and CO oxidation) stages of the converter. As in two-way converters, this injected air provides oxygen for the oxidation reactions. An upstream air injection point, ahead of the catalytic converter, is also sometimes present to provide additional oxygen only during the engine warm up period. This causes unburned fuel to ignite in the exhaust tract, thereby preventing it reaching the catalytic converter at all. This technique reduces the engine runtime needed for the catalytic converter to reach its "light-off" or operating temperature.

Most newer vehicles have electronic fuel injection systems, and do not require air injection systems in their exhausts. Instead, they provide a precisely controlled air-fuel mixture that quickly and continually cycles between lean and rich combustion. Oxygen sensors monitor the exhaust oxygen content before and after the catalytic converter, and the engine control unit uses this information to adjust the fuel injection so as to prevent the first (NO
x
reduction) catalyst from becoming oxygen-loaded, while simultaneously ensuring the second (HC and CO oxidation) catalyst is sufficiently oxygen-saturated.

الضرر

Catalyst poisoning occurs when the catalytic converter is exposed to exhaust containing substances that coat the working surfaces, so that they cannot contact and react with the exhaust. The most notable contaminant is lead, so vehicles equipped with catalytic converters can run only on unleaded fuel. Other common catalyst poisons include sulfur, manganese (originating primarily from the gasoline additive MMT), and silicon, which can enter the exhaust stream if the engine has a leak that allows coolant into the combustion chamber. Phosphorus is another catalyst contaminant. Although phosphorus is no longer used in gasoline, it (and zinc, another low-level catalyst contaminant) was widely used in engine oil antiwear additives such as zinc dithiophosphate (ZDDP). Beginning in 2004, a limit of phosphorus concentration in engine oils was adopted in the API SM and ILSAC GF-4 specifications.

Depending on the contaminant, catalyst poisoning can sometimes be reversed by running the engine under a very heavy load for an extended period of time.[بحاجة لمصدر] The increased exhaust temperature can sometimes vaporize or sublimate the contaminant, removing it from the catalytic surface.[بحاجة لمصدر] However, removal of lead deposits in this manner is usually not possible because of lead's high boiling point.[بحاجة لمصدر]

Any condition that causes abnormally high levels of unburned hydrocarbons (raw or partially burnt fuel or oils) to reach the converter will tend to significantly elevate its temperature, bringing the risk of a meltdown of the substrate and resultant catalytic deactivation and severe exhaust restriction. These conditions include failure of the upstream components of the exhaust system (manifold/header assembly and associated clamps susceptible to rust/corrosion and/or fatigue e.g. the exhaust manifold splintering after repeated heat cycling), ignition system e.g. coil packs and/or primary ignition components (e.g. distributor cap, wires, ignition coil and spark plugs) and/or damaged fuel system components (fuel injectors, fuel pressure regulator, and associated sensors). Oil and/or coolant leaks, perhaps caused by a head gasket leak, can also cause high unburned hydrocarbons.

القوانين التنظيمية

Emissions regulations vary considerably from jurisdiction to jurisdiction. Most automobile spark-ignition engines in North America have been fitted with catalytic converters since 1975,[1][2][3][4] and the technology used in non-automotive applications is generally based on automotive technology. In many jurisdictions, it is illegal to remove or disable a catalytic converter for any reason other than its direct and immediate replacement. Nevertheless, some vehicle owners remove or "gut" the catalytic converter on their vehicle.[25][26] In such cases, the converter may be replaced by a welded-in section of ordinary pipe or a flanged "test pipe", ostensibly meant to check if the converter is clogged by comparing how the engine runs with and without the converter. This facilitates temporary reinstallation of the converter in order to pass an emission test.[27]

In the United States, it is a violation of Section 203(a)(3)(A) of the 1990 amended Clean Air Act for a vehicle repair shop to remove a converter from a vehicle, or cause a converter to be removed from a vehicle, except in order to replace it with another converter,[28] and Section 203(a)(3)(B) makes it illegal for any person to sell or to install any part that would bypass, defeat, or render inoperative any emission control system, device, or design element. Vehicles without functioning catalytic converters generally fail emission inspections. The automotive aftermarket supplies high-flow converters for vehicles with upgraded engines, or whose owners prefer an exhaust system with larger-than-stock capacity.[29]

الأثر على تدفق العادم

Faulty catalytic converters as well as undamaged early types of converters can restrict the flow of exhaust, which negatively affects vehicle performance and fuel economy.[25] Modern catalytic converters do not significantly restrict exhaust flow. A 2006 test on a 1999 Honda Civic, for example, showed that removing the stock catalytic converter netted only a 3% increase in maximum horsepower; a new metallic core converter only cost the car 1% horsepower, compared to no converter.[27]

المخاطر

Carburetors on pre-1981 vehicles without feedback fuel-air mixture control could easily provide too much fuel to the engine, which could cause the catalytic converter to overheat and potentially ignite flammable materials under the car.[30]


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

فترة التسخين

Vehicles fitted with catalytic converters emit most of their total pollution during the first five minutes of engine operation; for example, before the catalytic converter has warmed up sufficiently to be fully effective.[31]

In the early 2000s it became common to place the catalyst converter right next to the exhaust manifold, close to the engine, for much quicker warm-up. In 1995, Alpina introduced an electrically heated catalyst. Called "E-KAT," it was used in Alpina's B12 5,7 E-KAT based on the BMW 750i.[32] Heating coils inside the catalytic converter assemblies are electrified just after the engine is started, bringing the catalyst up to operating temperature very quickly to qualify the vehicle for low emission vehicle (LEV) designation.[33] BMW later introduced the same heated catalyst, developed jointly by Emitec, Alpina, and BMW,[32] in its 750i in 1999.[33]

Some vehicles contain a pre-cat, a small catalytic converter upstream of the main catalytic converter which heats up faster on vehicle start up, reducing the emissions associated with cold starts. A pre-cat is most commonly used by an auto manufacturer when trying to attain the Ultra Low Emissions Vehicle (ULEV) rating, such as on the Toyota MR2 Roadster.[34]

الوقع البيئي

Catalytic converters have proven to be reliable and effective in reducing noxious tailpipe emissions. However, they also have some shortcomings in use, and also adverse environmental impacts in production:

  • An engine equipped with a three-way catalyst must run at the stoichiometric point, which means more fuel is consumed than in a lean-burn engine. This means approximately 10% more CO2 emissions from the vehicle.
  • Catalytic converter production requires palladium or platinum; part of the world supply of these precious metals is produced near Norilsk, Russia, where the industry (among others) has caused Norilsk to be added to Time magazine's list of most-polluted places.[35]
  • The extreme heat of the converters themselves[36] can cause wildfires, especially in dry areas.[37][38][39]

السرقة

Because of the external location and the use of valuable precious metals including platinum, palladium and rhodium, catalytic converters are a target for thieves. The problem is especially common among late-model trucks and SUVs, because of their high ground clearance and easily removed bolt-on catalytic converters. Welded-on converters are also at risk of theft, as they can be easily cut off.[40][41][42] Pipecutters are often used to quietly remove the converter[43][44] but other tools such as a portable reciprocating saw can damage other components of the car, such as the alternator, wiring or fuel lines, with potentially dangerous consequences. Rising metal prices in the U.S. during the 2000s commodities boom led to a significant increase in converter theft. A catalytic converter can cost more than $1,000 to replace, more if the vehicle is damaged during the theft.[45][46][47]

From 2019–2020, thieves in the United Kingdom were targeting older-model hybrid cars which have more precious metals than newer vehicles—sometimes worth more than the value of the car—leading to scarcity and long delays in replacing them.[48]

In 2021 a trend emerged in the Democratic Republic of Congo where catalytic converters were stolen for use in drug production.[49]

التشخيص

Various jurisdictions now require on-board diagnostics to monitor the function and condition of the emissions-control system, including the catalytic converter. Vehicles equipped with OBD-II diagnostic systems are designed to alert the driver to a misfire condition by means of illuminating the "check engine" light on the dashboard, or flashing it if the current misfire conditions are severe enough to potentially damage the catalytic converter.[بحاجة لمصدر]

On-board diagnostic systems take several forms.

Temperature sensors are used for two purposes. The first is as a warning system, typically on two-way catalytic converters such as are still sometimes used on LPG forklifts. The function of the sensor is to warn of catalytic converter temperature above the safe limit of 750 °C (1,380 °F). Modern catalytic-converter designs are not as susceptible to temperature damage and can withstand sustained temperatures of 900 °C (1,650 °F).[بحاجة لمصدر] Temperature sensors are also used to monitor catalyst functioning: usually two sensors will be fitted, with one before the catalyst and one after to monitor the temperature rise over the catalytic-converter core.[بحاجة لمصدر]

The oxygen sensor is the basis of the closed-loop control system on a spark-ignited rich-burn engine; however, it is also used for diagnostics. In vehicles with OBD II, a second oxygen sensor is fitted after the catalytic converter to monitor the O2 levels. The O2 levels are monitored to see the efficiency of the burn process. The on-board computer makes comparisons between the readings of the two sensors. The readings are taken by voltage measurements. If both sensors show the same output or the rear O2 is "switching", the computer recognizes that the catalytic converter either is not functioning or has been removed, and will operate a malfunction indicator lamp and affect engine performance. Simple "oxygen sensor simulators" have been developed to circumvent this problem by simulating the change across the catalytic converter with plans and pre-assembled devices available on the Internet. Although these are not legal for on-road use, they have been used with mixed results.[50] Similar devices apply an offset to the sensor signals, allowing the engine to run a more fuel-economical lean burn that may, however, damage the engine or the catalytic converter.[51]

NO
x
sensors are extremely expensive and are in general used only when a compression-ignition engine is fitted with a selective catalytic-reduction (SCR) converter, or a NO
x
absorber in a feedback system. When fitted to an SCR system, there may be one or two sensors. When one sensor is fitted it will be pre-catalyst; when two are fitted, the second one will be post-catalyst. They are used for the same reasons and in the same manner as an oxygen sensor; the only difference is the substance being monitored.[بحاجة لمصدر]

انظر أيضاً

الهامش

  1. ^ أ ب ت ث Palucka, Tim (Winter 2004). "Doing the Impossible". Invention & Technology. 19 (3). Archived from the original on 3 December 2008. Retrieved 14 December 2011.
  2. ^ أ ب Petersen Publishing (1975). "The Catalytic Converter". The Petersen Automotive Troubleshooting & Repair Manual. New York, NY: Grosset & Dunlap. p. 493. ISBN 0-448-11946-3. For years, the exhaust system (...) remained virtually unchanged until 1975 when a strange new component was added. It's called a catalytic converter(...) {{cite book}}: Unknown parameter |editors= ignored (|editor= suggested) (help)
  3. ^ أ ب "General Motors Believes it has an Answer to the Automotive Air Pollution Problem". The Blade: Toledo, Ohio. 12 September 1974. Retrieved 14 December 2011.
  4. ^ أ ب "Catalytic Converter Heads Auto Fuel Economy Efforts". The Milwaukee Sentinel. 11 November 1974. Retrieved 14 December 2011.
  5. ^ "Choosing the Right Wood Stove". Burn Wise. US EPA. Retrieved 2 January 2012.
  6. ^ https://www.catalyticconverterrecycling.com
  7. ^ Csere, Csaba (January 1988). "10 Best Engineering Breakthroughs". Car and Driver. 33 (7): 63.
  8. ^ "Exhaust Gas Made Safe" Popular Mechanics, September 1951, p. 134, bottom of page
  9. ^ "His Smoke Eating Cats Now Attack Traffic Smog". Popular Science, June 1955, pp. 83-85/244.
  10. ^ "Eugene Houdry". Chemical Heritage Foundation. Retrieved 27 October 2016.
  11. ^ قالب:Registration required "Carl D. Keith, a Father of the Catalytic Converter, Dies at 88". The New York Times. 15 November 2008.
  12. ^ Staff writer (undated). "Engelhard Corporation". referenceforbusiness.com. Retrieved 7 January 2011.
  13. ^ Robert N. Carter, Lance L. Smith, Hasan Karim, Marco Castaldi, Shah Etemad, George Muench, R. Samuel Boorse, Paul Menacherry and William C. Pfefferle (1998). "Catalytic Combustion Technology Development for Gas Turbine Engine Applications". MRS Proceedings, 549, 93 doi:10.1557/PROC-549-93
  14. ^ Worthy, Sharon. "Connecticut chemist receives award for cleaner air technology". Bio-Medicine. 23 June 2003. Retrieved 11 December 2012.
  15. ^ أ ب Pischinger, Univ.-Prof. Dr.-Ing. Stephan (2011). Verbrennungsmotoren Band 2 (24 ed.). Aachen, Germany: Lehrstuhl Für Verbrennungskraftmachinen. p. 335.
  16. ^ Martin Votsmeier, Thomas Kreuzer, Jürgen Gieshoff, Gerhard Lepperhoff. Automobile exhaust Control, in Ullmann's Encyclopedia of Industrial Chemistry, Wiley-VCH 2002. DOI: 10.1002/14356007.a03_189.pub2
  17. ^ Kašpar, J.; Fornasiero, P.; Graziani, M. (1999). "Use of CeO2-based oxides in the three-way catalysis". Catalysis Today. 50 (2): 285–298. doi:10.1016/S0920-5861(98)00510-0. ISSN 0920-5861.
  18. ^ أ ب "Automotive Catalytic Converters: Current Status and Some Perspectives". Catalysis Today. 77 (4): 419–449. 2003. doi:10.1016/S0920-5861(02)00384-X. {{cite journal}}: Cite uses deprecated parameter |authors= (help)
  19. ^ "The three way catalytic converter".
  20. ^ Brandt, Erich; Wang, Yanying; Grizzle, Jessy (2000). "Dynamic Modeling of a Three Way Catalyst for SI Engine Exhaust Emission Control" (PDF). IEEE Transactions on Control Systems Technology. 8 (5): 767–776. doi:10.1109/87.865850.
  21. ^ "The three way catalytic converter".
  22. ^ "Durability of Platinum-Containing Automotive Exhaust Control Catalysts".
  23. ^ "Air Pollution Control Technology Fact Sheet (PDF, US Environmental Protection Agency)" (PDF).
  24. ^ "Heavy-Duty Engine and Vehicle Standards and Highway Diesel Fuel Sulfur Control Requirements" (PDF). 2015-08-19. (123 KB)
  25. ^ أ ب Crutsinger, Martin (29 September 1982). "Kits to Foil Auto Pollution Control Are Selling Well". The Gainesville Sun.
  26. ^ "Some of Us Can Only Afford a Clunker". The Palm Beach Post. 23 February 1996.
  27. ^ أ ب "Beat the Law". Import Tuner. 1 October 2006. Archived from the original on 28 February 2014. Retrieved 9 January 2011.
  28. ^ Sale and Use of Aftermarket Catalytic Converters, US Environmental Protection Agency, US Federal Register Volume 51
  29. ^ Tanner, Keith. Mazda MX-5 Miata. p. 120. {{cite book}}: |work= ignored (help)
  30. ^ Ullman, Owen (14 June 1976). "Catalytic Converter Still Controversial after Two Years of Use". The Bulletin[مطلوب توضيح].
  31. ^ Catalytic converters, nsls.bnl.gov
  32. ^ أ ب "Milestones". alpina-automobiles.com. Archived from the original on 30 June 2015. Retrieved 5 June 2015.
  33. ^ أ ب Edgar, Julian (5 October 1999). "Goodbye 12 volts... hello 42 volts!". Autospeed. Archived from the original on 28 May 2012. Retrieved 2 January 2012. The current model BMW 750iL has a maximum electrical load of 428 amps (5.9 kW)! In this car, over half of the maximum load is from the short-term electrical heating of the catalytic converters
  34. ^ "Pre-cats - What You Should Know". Toyota Owners Club - Toyota Forum. Retrieved 15 April 2018.
  35. ^ Walsh, Bryan (12 September 2007). "Norilsk, Russia". The World's Most Polluted Places. Time. Archived from the original on 31 October 2007. Retrieved 7 January 2011.
  36. ^ "Here's how to avoid accidentally starting the next firestorm". pe.com. 6 September 2016.
  37. ^ "Catalytic converter-started fires are common". ocregister.com. 18 November 2008. Retrieved 15 April 2018.
  38. ^ "Catalytic converter blamed for causing SR-52 brush fire". fox5sandiego.com. 29 June 2017. Retrieved 15 April 2018.
  39. ^ "Archived copy". Archived from the original on 14 July 2017. Retrieved 2017-07-14.{{cite web}}: CS1 maint: archived copy as title (link)
  40. ^ Fraga, Brian (30 November 2011). "Carver police investigating catalytic converter thefts". South Coast Today. Retrieved 21 December 2011.
  41. ^ Medici, Joe (31 July 2007). "Underhanded thieves". Chroniclet.com. Archived from the original on 2007-09-28.
  42. ^ Murr, Andrew (9 January 2008). "An Exhausting New Crime — What Thieves Are Stealing from Today's Cars". Newsweek. Retrieved 7 January 2011.
  43. ^ "Catalytic converters are being stolen for valuable metals". 11 December 2019 – via www.rte.ie. {{cite journal}}: Cite journal requires |journal= (help)
  44. ^ "Cotati police bust catalytic converter theft suspects". 29 November 2019.
  45. ^ "Thieves Nationwide Are Slithering Under Cars, Swiping Catalytic Converters". The New York Times. 9 February 2021. Archived from the original on 2021-12-28.
  46. ^ Johnson, Alex (12 February 2008). "Stolen in 60 Seconds: The Treasure in Your Car — As Precious Metals Prices Soar, Catalytic Converters Are Targets for Thieves". NBC News. Retrieved 7 January 2011.
  47. ^ "Converters Taken by Car Lot Thieves". PoconoNews. 2 July 2009.
  48. ^ "Catalytic converter theft: hybrid car owners face insurance nightmare". the Guardian (in الإنجليزية). 2020-02-01.
  49. ^ Nyemba, Benoit (27 September 2021). "Car-exhaust drug craze alarms Congo's capital". Reuters (in الإنجليزية). Retrieved 8 October 2021.
  50. ^ "Settlement Involves Illegal Emission Control 'Defeat Devices' Sold for Autos". 1 June 2007.
  51. ^ "Check Engine Lights Come on for a Reason". Concord Monitor. 12 January 2003.

للاستزادة

  • Keith, C. D., et al. U.S. Patent 3٬441٬381 : "Apparatus for purifying exhaust gases of an internal combustion engine". 29 April 1969
  • Lachman, I. M. et al. U.S. Patent 3٬885٬977 : "Anisotropic Cordierite Monolith" (Ceramic substrate). 5 November 1973
  • Charles H. Bailey. U.S. Patent 4٬094٬645 : "Combination muffler and catalytic converter having low backpressure". 13 June 1978
  • Charles H. Bailey. U.S. Patent 4٬250٬146 : '"Caseless monolithic catalytic converter". 10 February 1981
  • Srinivasan Gopalakrishnan. GB patent 2397782: "Process And Synthesizer For Molecular Engineering of Materials". 13 March 2002.

وصلات خارجية

الكلمات الدالة: